Difference between revisions of "Game Boy DMG-01 Full Size IPS Installation"

From TechWiki
Jump to navigation Jump to search
(Assembly: Final)
 
(One intermediate revision by the same user not shown)
Line 3: Line 3:
 
The manufacturer includes double sided tape to fix the LCD to the upper shell.  Due to the fragile construction of the LCD panel, we have designed a drop-in bracket and these install directions are written based on this bracket.  '''We strongly recommend against installing the panel with tape!'''  Repositioning the screen to center the display will be very challenging and future removal will be even worse once the tape has bonded with the shell.
 
The manufacturer includes double sided tape to fix the LCD to the upper shell.  Due to the fragile construction of the LCD panel, we have designed a drop-in bracket and these install directions are written based on this bracket.  '''We strongly recommend against installing the panel with tape!'''  Repositioning the screen to center the display will be very challenging and future removal will be even worse once the tape has bonded with the shell.
  
You may notice that the full size replacement PCB for the upper shell has 4 slots that correspond with 4 tabs on the back of the LCD.  The manufacturer has applied anti-shorting tape to the panel which prevents these tabs from being used.  We don't recommend using this method either as the image will not be centered by default.  If you do bend the tabs to center the image, the metal tabs will end up at a 45 degree angle and the screen will wobble / float.  Alignment issues are further exacerbated as you can only utilize 3 out of 4 tabs due to the location of the miniature LCD driver PCB.
+
You may notice that the full size replacement PCB for the upper shell has 4 slots that correspond with 4 tabs on the back of the LCD.  The manufacturer may have applied anti-shorting tape to the LCD panel which prevents these tabs from being used.  We don't recommend using this method either as the image will not be centered by default.  If you do bend the tabs to center the image, the metal tabs will end up at a 45 degree angle and the screen will wobble / float.  Alignment issues are further exacerbated as you can only utilize 3 out of 4 tabs due to the location of the miniature LCD driver PCB.
  
 +
We have had multiple reports of damage to the LCD when using the tabs.  '''Do not use them!'''
  
 
== Tools Required ==
 
== Tools Required ==
Line 61: Line 62:
 
#Remove new PCB, replace buttons and conductive pads
 
#Remove new PCB, replace buttons and conductive pads
 
#Secure and fasten LCD PCB to upper shell at 6 points shown in photo below
 
#Secure and fasten LCD PCB to upper shell at 6 points shown in photo below
#Close shell and replace 6x shell screws
+
#Close shell and replace 6x shell screws.  Note that extra resistance is normal due to folding the large connecting ribbon between boards.
 
<gallery>
 
<gallery>
 
File:New-PCB-fixed-to-shell.jpg|Locations of 6 screws for fixing new LCD to upper shell
 
File:New-PCB-fixed-to-shell.jpg|Locations of 6 screws for fixing new LCD to upper shell
 
</gallery>
 
</gallery>

Latest revision as of 13:18, 24 March 2020

Support / Install page for our full-size replacement display & PCB for the Game Boy DMG-01

Notes

The manufacturer includes double sided tape to fix the LCD to the upper shell. Due to the fragile construction of the LCD panel, we have designed a drop-in bracket and these install directions are written based on this bracket. We strongly recommend against installing the panel with tape! Repositioning the screen to center the display will be very challenging and future removal will be even worse once the tape has bonded with the shell.

You may notice that the full size replacement PCB for the upper shell has 4 slots that correspond with 4 tabs on the back of the LCD. The manufacturer may have applied anti-shorting tape to the LCD panel which prevents these tabs from being used. We don't recommend using this method either as the image will not be centered by default. If you do bend the tabs to center the image, the metal tabs will end up at a 45 degree angle and the screen will wobble / float. Alignment issues are further exacerbated as you can only utilize 3 out of 4 tabs due to the location of the miniature LCD driver PCB.

We have had multiple reports of damage to the LCD when using the tabs. Do not use them!

Tools Required

  1. Philips or Triwing screwdriver
  2. Soldering iron & solder
  3. Diagonal cutters
  4. Hobby knife


Disassembly

  1. Remove battery cover & batteries
  2. Remove 6 screws holding shell together (4 exposed, 2 inside battery compartment)
  3. Detach ribbon cable connecting CPU & LCD boards
  4. Remove 10 screws holding DMGLCD board to upper shell
  5. Remove DMGLCD board, pads, buttons, and set aside


Prep

  1. Flush cut 2x original LCD screw posts
  2. Flush cut 1x shell tab
  3. Flush cut edge trim opposite of contrast wheel
  4. Inspect CPU PCB soldering and flush-cut solder points


Assembly: Part 1

  1. Desolder and swap speaker to new PCB
  2. Gently bend alignment bracket and snap new LCD in to place.
  3. Connect LCD interface board to LCD. This is a double-row connector - ensure ribbon is fully seated into the interface PCB before closing the connector lock.
  4. Cut and apply a very small piece of double-sided tape and attach interface PCB to back of LCD
  5. Connect thin flat cable to interface PCB
  6. Insert bracket/LCD into upper shell
  7. Temporarily refit new PCB and connect LCD
  8. Connect large ribbon cable between new PCB and CPU board.


Testing

  1. Align upper and lower shell, replace middle 2 screws to close case fully for binding check (listed below)
  2. Power on unit
  3. Test contrast wheel for binding.
    1. If wheel does not spin freely, ensure shell tab is fully removed and that case screws are not over tightened.
    2. If palette button binds, check wheel for witness marks indicating drag against DMGCPU board solder connections.


Assembly: Final

  1. Remove new PCB, replace buttons and conductive pads
  2. Secure and fasten LCD PCB to upper shell at 6 points shown in photo below
  3. Close shell and replace 6x shell screws. Note that extra resistance is normal due to folding the large connecting ribbon between boards.